Customization: | Available |
---|---|
Application: | Transformer Oil |
Voltage: | 380V |
Suppliers with verified business licenses
Audited by an independent third-party inspection agency
Parameters
|
Model Unit |
ZYD-T-W-30
|
ZYD-T-W-50
|
ZYD-T-W-100
|
ZYD-T-W-150
|
ZYD-T-W-200
|
ZYD-T-W-250
|
ZYD-T-W-300
|
|
Flow Rate
|
Liter/hour
|
1,800
|
3,000
|
6,000
|
10,000
|
12,000
|
15,000
|
18,000
|
|
Recommended Max. oil volume in one storage tank
|
Tons
|
6
|
12
|
24
|
40
|
60
|
90
|
110
|
|
Relative Working
Vacuum Degree |
MPa
|
-0.08 ~ -0.099 MPa
|
|||||||
Absolute Operating
Vacuum Level |
Pa
|
≤ 8 Pa
|
|||||||
Working Discharge Pressure
|
MPa
|
≤ 0.5
|
|||||||
Temperature Control
|
ºC
|
0 ~ 100
|
|||||||
Operation Oil Temperature
in Treatment |
ºC
|
30 ~ 80 (65ºC is best)
|
|||||||
Power Supply
|
|
AC 3~, 380 V, 50Hz, 4 Wire (or as per your requirements)
|
|||||||
Operation Mode
|
|
Continuous Operation
|
|||||||
Working hours
without Trouble |
Hour
|
4000
|
|||||||
Continuous Working Hours
|
Hour
|
150
|
|||||||
Ambient Temperature
|
|
-25 ~ 55ºC
|
|||||||
Working Noise
|
dB(A)
|
65 ~ 85
|
|||||||
Cooling Method
|
|
Air Cooling
|
|||||||
Heating Power
(adjusted available) |
KW
|
30
|
72
|
90
|
120
|
135
|
150
|
180
|
|
Total Power
|
KW
|
36
|
78
|
105
|
136
|
150
|
170
|
206
|
|
Inlet/Outlet
|
mm
|
φ25
|
Φ32
|
φ50
|
φ50
|
φ50
|
φ60
|
φ60
|
|
Weight
|
Kg
|
500
|
900
|
1200
|
1400
|
1650
|
1800
|
1950
|
|
Dimension
|
Length
|
mm
|
1380
|
1710
|
1800
|
2010
|
2060
|
2100
|
2200
|
Width
|
mm
|
1020
|
1510
|
1560
|
2030
|
2100
|
2150
|
2250
|
|
Height
|
mm
|
1760
|
1860
|
2080
|
2080
|
2200
|
2450
|
2550
|
|
After Treatment
|
|||||||||
Dielectric Strength
|
kV
|
≥ 70 ~ 80
|
|||||||
Water Content
|
PPM
|
≤ 3 ~ 5
|
|||||||
Gas Content
|
%
|
≤ 0.1
|
|||||||
Particle Size
|
μm
|
≤ 3
|
|||||||
Cleanliness
|
|
≤NAS 1638 Grade 5
|
|||||||
Note: 1. The dimension and weight will be changed with changing of technical specs.
2. All the specs can be customized according to client's requirements. |
1.ZYD-T-W adopt double vacuum separation technology, double stages thin film drying degassing technology, double evaporation area and degassing time.
2.Patented degassing tank: anti-foam structure & dual electronic foam monitoring system ( key components are from Switzerland), completely eradicating oil entering into vacuum pump.
Routine Maintenance Procedures
Filter element inspection, cleaning and replacement
|
After the filter element has been working for a period of time, when the pressure difference through the filter element increases to the design limit due to the clogging of dirt, the filter element must be maintained, including cleaning or replacement. The material and structure of the filter element determine whether it can be cleaned and how to clean it.
|
Note: Among the filter elements used in ZYD-T-W, the coarse filter element FL01 can be cleaned. Fine filter elements FL02, FL03 and vacuum pump oil filter elements cannot be cleaned and must be replaced.
|
|
Coarse filter element cleaning and replacement
|
When the vacuum degree reaches -0.07~-0.1Mpa, the oil viscosity is low, the oil inlet solenoid valve (SV01, SV02) is fully opened, and the oil inlet speed is still slower than the oil discharge speed of the oil pump, stop the machine and remove the suction filter. Net maintenance. The filter element can be cleaned in gasoline or alkaline cleaning solution, and the dirt attached to the mesh is blown away from the inside to the outside with compressed air. Before installation, check whether the filter screen is damaged, and replace it if found damaged.
|